Top 9 Dewalt Zero Clearance Insert For Dewalt Table Saw

Product description

Leecraft model DW-2 fits DeWalt: DW744 & DW745 (factory splitter/guard incompatible with DW-2 insert on these saws); DW746 & DeWalt DWE7480, DWE7490X, DWE7491RS, DWE7499GD. LEECRAFT Phenolic Inserts and Sheet Stock reduce splintering and chip-out on the bottom side of regular or dado table saw cuts. Simply raise your saw blade through the insert to create a “kerf” which precisely matches the blade on your saw. Complete with instructions. Insert surface colors may vary.

Amazon.com

The Leecraft Zero-Clearance Table Saw Insert for DeWalt DW744 and DW746 offers superior rigidity, flatness, durability, and low friction. This product is user-friendly with top-accessible leveling screws, lateral adjustment screws for a vibration-free fit, a rear anti-life pin, and a precut blade bottom pocket. It significantly reduces saw noise and dust, as well as chip-out and splintering. This saw insert is constructed of high-density phenolic laminate with a bonded-melamine surface to ensure a long life. It fits eWalt DW744 and DW746; instructions are included and the kerf serves as a handy stock alignment guide. This product measures 13-5/8-by-3-3/4-by-1/2-inch (length by width by thickness).

See all Product description

The DEWALT DWE7402DI Dado Throatplate for 10″ Portable Table Saw allows for use of stacked dado cutters. This insert is designed to be used with DWE7490 and DWE7491 Table saw versions . For woodworkers, carpenters, remodelers, deck builders.

Replace your factory table saw insert with a phenolic zero clearance insert. Zero Clearance inserts help prevent kickback and tear-out on your stock pieces when feeding through a table saw blade. By raising your blade up through the insert, you eliminate gaps between the side of the insert and the blade. This provides with much better stock support than with most factory inserts that come with the saw. This also prevents smaller stock pieces from falling into the opening that exists with factory inserts. Zero clearance inserts can be used with any type of standard carbide tipped saw blade (standard or thin kerf blades) and can also be used with dado blades. It is recommended that if you need an insert to accommodate both a standard saw blade and a dado blade, that you purchase two separate zero clearance inserts. Use one for your normal cuts and one for dado cuts. Actual Color May Vary.

Product description

LEECRAFT Phenolic Inserts and Sheet Stock reduce splintering and chip-out on the bottom side of regular or dado table saw cuts. Simply raise your saw blade through the insert to create a “kerf” which precisely matches the blade on your saw. This 1/2″ thick insert is precision machined from a nearly frictionless melamine faced, high density phenolic laminate. It offers durability and flatness unobtainable from cheaper plastic inserts. Features like top mounted set screws for precise leveling, front/side adjustment screws for perfect side to side and front to rear fit, and a rear safety pin that keeps the rear of the insert in place, make this the best insert we have ever seen. Sheet stock material (1/2″ x 11″ x 15″) is perfect for creating your own custom jigs and fixtures. Craftsman insert measures 14″ x 3-3/4″ and fits most new, 10″ belt drive models. (Check the opening of your Sears saw before ordering). Complete with instructions. Insert surface colors may vary.

From the Manufacturer

The “zero clearance” concept is simple: The blade cuts its own perfectly sized slot by being raised through a machinable “blank” insert. Leecraft inserts are 1/2-inch-thick, high-density phenolic laminate, with bonded-melamine surface. They offer superior rigidity, flatness, durability, and low friction. User-friendly features include top-accessible leveling screws, lateral adjustment screws for a vibration-free fit, rear anti-lift pin (except JT-1), and a precut-blade bottom pocket that provides clearance for fully retracted blades and bevel cuts. Instructions included. Use carbide-tipped blades only. Fits Craftsman (Sears). Size: 14 by 3-3/4 inches.

The MJ SPLITTER system is a low profile splitter that is simple to install, and obtains effective results by keeping stock burn free, and reduces kick back as well as providing a mini feather board effect. MJ SPLITTER is designed to be installed into a zero-clearance insert, and the MJ SPLITTER comes with installation guide, drill guide and drill bit for installation. Each package comes with two MJ SPLITTERs. The Thin Kerf Splitter (YELLOW COLORED) is designed for kerf ranges: 0.090″ to 0.118″. Always use the correct MJ SPLIITER corresponding to your saw blade. Packages do not include zero-clearance inserts. Only use for 90 degree cuts. Made in the USA.

The ML SPLITTER SteelPro is our toughest table saw splitter yet. Virtually eliminate kickback and prevent wood burning on your table saw. Consider a core made of stainless steel and then coated with smooth high density ABS plastic–that is the SteelPro. MJ SPLITTER SteelPro is designed for 1/8″ Kerf saw blades range: (0.118″ – 0.145″). Each package comes with 4 SteelPro Splitters, 4 Kerf Keepers, installation guide, drill guide, and drill bit for easy installation. The Dual Splitter approach will utilize our mini-feather board effect to off-set both sides of the work piece, keeper piece and off-cut piece. Each SteelPro Splitter is fine-tuned to several thousands of an inch to keep pressure off the keeper piece against the fence. Once installed, you’ll be able to plug and play with the SteelPro because each Splitter comes with a different offset marked on each with a “+.” And each “+” represents 0.003” up to “+++” which is 0.009”. We have also included our Kerf Keepers which are designed to prevent binding from warping reactive solid wood. Always use the correct MJ SPLITTER SteelPro in correspondence to your kerf range. Only for 90 degree cuts. Made in the USA. Made by MICROJIG. Watch the Action Video and Add to Your Cart Today! Work safer. Work Smarter

Our Promise to Readers

We keep receiving tons of questions of readers who are going to buy Dewalt Zero Clearance Insert For Dewalt Table Saw, eg:

• What are Top 10 Dewalt Zero Clearance Insert For Dewalt Table Saw for 2020, for 2019, for 2018 or even 2017 (old models)?
• What is Top 10 Dewalt Zero Clearance Insert For Dewalt Table Saw to buy?
• What are Top Rated Dewalt Zero Clearance Insert For Dewalt Table Saw to buy on the market?
• or even What is Top 10 affordable (best budget, best cheap or even best expensive!!!) Dewalt Zero Clearance Insert For Dewalt Table Saw?…
• All of these above questions make you crazy whenever coming up with them. We know your feelings because we used to be in this weird situation when searching for Dewalt Zero Clearance Insert For Dewalt Table Saw.
• Before deciding to buy any Dewalt Zero Clearance Insert For Dewalt Table Saw, make sure you research and read carefully the buying guide somewhere else from trusted sources. We will not repeat it here to save your time.
• You will know how you should choose Dewalt Zero Clearance Insert For Dewalt Table Saw and What you should consider when buying the Dewalt Zero Clearance Insert For Dewalt Table Saw and Where to Buy or Purchase the Dewalt Zero Clearance Insert For Dewalt Table Saw. Just consider our rankings above as a suggestion. The final choice is yours.
• That’s why we use Big Data and AI to solve the issue. We use our own invented, special algorithms to generate lists of Top 10 brands and give them our own Scores to rank them from 1st to 10th.
• You could see the top 10 Dewalt Zero Clearance Insert For Dewalt Table Saw of 2020 above. The lists of best products are updated regularly, so you can be sure that the information provided is up-to-date.
• You may read more about us to know what we have achieved so far. Don’t hesitate to contact us if something’s wrong or mislead information about Dewalt Zero Clearance Insert For Dewalt Table Saw.